Standard CMOS Setup:

Date (mm:dd:yy) : Current Date
Time (hh:mm:ss) : Current Time

Hard Disks:         Type:  Size:  Cyls:  Head:  Precomp:  Landz:  Sector:  Mode:
Primary Master     Auto   0       0       0         0               0          0        Auto
Primary Slave       None   0       0       0         0               0	         0        ---
Sec Master          Auto   0       0       0         0               0          0	       Auto
Sec Slave            None	  0       0       0         0               0          0 	      ---

Drive A: 1.44M, 3.5 in.
Drive B: None

Video: EGA/VGA
Halt On: All, But Keyboard

Base Memory: 640K
Extended Memory: 64512K
Other Memory: 384K
Total Memory: 65536K




**NOTE: DO NOT use the IDE HDD AUTO DETECTION utility located in the main BIOS screen to mount IDE hard drives. Instead, set the "Type" field for the Primary Master and Secondary Master drives in the drive setup menu above to "Auto." This will cause the BIOS to automatically detect any changes in drive status each time the HDR boots up.**

BIOS Features Setup:

Virus Warning : Disabled
CPU L1 Cache : Enabled
CPU L2 Cache : Enabled
CPU L2 Cache ECC Checking : Enabled
Quick Power On Self Test : Enabled
Boot Sequence : A,C,SCSI
Swap Floppy Drive : Disabled
Boot Up Floppy Seek : Disabled
Boot Up NumLock Status : On
Typematic Rate Setting : Disabled
Typematic Rate (Chars/Sec) : 6
Typematic Delay (Msec) : 250
Security Option : Setup
PCI/VGA Palette Snoop : Disabled
OS Select For DRAM > 64MB : Non-OS2
HDD S.M.A.R.T. Capability : Disabled

Chipset Features Setup:

SDRAM RAS-to-CAS Delay : 3
SDRAM RAS Precharge Time : 3
SDRAM CAS Latency Time : 3
SDRAM Precharge Control : Disabled
DRAM Data Integrity Mode : Non-ECC
System BIOS Cacheable : Disabled
Video BIOS Cacheable : Disabled
Video RAM Cacheable : Disabled
8 Bit I/O Recovery Time : 1
16 Bit I/O Recovery Time : 1
Memory Hole At 15M-16M : Disabled
PCI 2.1 Compliance : Enabled
AGP Aperture Size (MB) : 64
CPU/PCI Clock (MHz) : Default
Spread Spectrum : Enabled

Power Management Setup:

ACPI Function : Disabled
Power Management : User Define
PM Control By APM : Yes
Video Off Method : DPMS
Video Off After : Suspend
MODEM Use IRQ : NA
Standby Mode : Disabled
Suspend Mode : Disabled
HDD Power Down : Disabled
PCI/VGA Act-Monitor : Disabled
Soft-Off by PWR-BTTN : Instant-Off
PWR Lost Resume State : Keep Off
Resume on Ring : Disabled
Resume on LAN : Disabled
Resume on Alarm : Disabled

PCI/PNP Configuration:

Resources Controlled By : Manual Assign IRQ for VGA : Disabled
Reset Configuration Data : Disabled Assign IRQ for USB : Disabled
PCI Slot 1 Use IRQ : Auto
PCI Slot 2 Use IRQ : Auto
PCI Slot 3 Use IRQ : Auto
PCI Slot 4 Use IRQ : Auto

IRQ-3 Assigned to : PCI/ISA PnP Used MEM Base Address : N/A
IRQ-4 Assigned to : PCI/ISA PnP
IRQ-5 Assigned to : PCI/ISA PnP
IRQ-7 Assigned to : PCI/ISA PnP
IRQ-9 Assigned to : PCI/ISA PnP
IRQ-10 Assigned to : Legacy ISA
IRQ-11 Assigned to : PCI/ISA PnP
IRQ-12 Assigned to : PCI/ISA PnP
IRQ-14Assigned to : PCI/ISA PnP
IRQ-15Assigned to : PCI/ISA PnP
DMA-0 Assigned to : PCI/ISA PnP
DMA-1 Assigned to : PCI/ISA PnP
DMA-3 Assigned to : PCI/ISA PnP
DMA-5 Assigned to : PCI/ISA PnP
DMA-6 Assigned to : PCI/ISA PnP
DMA-7 Assigned to : PCI/ISA PnP

Integrated Peripherals Setup:


IDE HDD Block Mode : Enabled
IDE Primary Master PIO : Auto
IDE Primary Slave PIO : Auto
IDE Secondary Master PIO : Auto
IDE Secondary Slave PIO : Auto
IDE Primary Master UDMA : Auto
IDE Primary Slave UDMA : Auto
IDE Secondary Master UDMA : Auto
IDE Secondary Slave UDMA : Auto
On-Chip Primary PCI IDE : Enabled
On-Chip Secondary PCI IDE : Enabled
USB Keyboard Support : Disabled
Init Display First : AGP
KBC Input Clock : 8 MHz
Onboard FDC Controller : Enabled
Onboard Serial Port 1 : 3F8/IRQ4
Onboard Serial Port 2 : 2F8/IRQ3
UART2 Mode Select : Normal

Onboard Parallel Port : Disabled


Keyboard/Mouse Power On : Disabled


***NOTE: Be sure that the onboard Parallel Port is Disabled in this setup.***